ABA Asphalt Binder Analyzer
The ABA Asphalt Binder Analyzer is used to determine the asphalt binder content of hot mix
asphalt/bituminous mixtures by the method of loss on ignition. The system combines a sophisticated
furnace and weighing system to continuously measure the weight loss of a bituminous mixture
during combustion and automatically calculates its binder content at the end of the test.
Apparatus for Distillation of Cutback Asphalt
The SCTAS-0500 is used for the examination of cut-back asphaltic materials by the distillation test. The apparatus consists of a distillation flask, condenser, adapter, shield, electric heater with thermoregulator, cylinder receiver, thermometer -2 +400°C shield and flask support.
Automatic Electronic Penetrometer
The SCTAS-0126 Automatic Electronic Penetrometer is used for determination of the needle penetration according to EN 1426, ASTM D5 and AASHTO T49 standards. The penetration depth of the needle is determined with a pulse type electronic measuring system, which is separated from the plunger during the test, this allows the free guidance of the plunger which virtually eliminates friction during the test.
Before each start of the test the measuring system automatically resets, and then the penetration
needle moves down to the sample by using the electric drive, the needle position can be finely adjusted by using the joystick located on the front panel. A magnifying glass and an ultra- bright LED
lamp are supplied to assist the operator; the plunger is then automatically released onto the sample
and raised automatically after the testing period. The test result is displayed on the digital display.
The plunger can easily be removed to calibrate its weight.
Automatic Marshall Compactor
Automatic, Marshall Compactors are designed to provide a stable and
rigid mechanism is used for preparation of bituminous specimens for
Marshall Stability tests.
SCTAS-0082/A model Compactor is for compaction of 4” dia. specimens
and SCTAS- 0084/ A model Compactor is for 6”dia. specimens.
Both models feature a heavy-duty design, which stands up well to the constant jarring caused by the
compaction process. The Coppactors are equipped with a mould fixing mechanism which also raises the hammer to provide easy removing of the mould. With this feature, the user can easily release the
mould and raise the rammer simultaneously.
Automatic Marshall Stability Test Machine
SCBC100 TFT Graphic Display Data Acquisition and Control Unit is designed to control the machine
and processing of data from load-cells, pressure transducers or displacement transducers which are
fitted to the machine.
All the operations of SCBC100 are controlled from the front panel consisting of a 800×480 pixel 65535
color resistive touch screen display and function keys. One analog channel for load cell and one
analog channel for displacement transducer exists.
SCBC100 has easy to use menu options. It displays all menu option listings simultaneously, allowing
the operator to access the required option in a seemless manner to activate the option or enter a
numeric value to set the test parameters. Its specimen setting sub-menu lists different specimen
types including but not limited to cube, cylinder, block, beam, beam double upper bearers, cube
splitting tensile, cylinder splitting tensile, paving block splitting tensile and kerb flexure. The SCBC100
digital graphic display is able to draw real-time “Load vs. Time”, “Load vs. Displacement” or “Stress
vs. Time” graphics.
SCBC100 unit offers many addition unique features. You can save more than 10000 test results in its
internal memory. SCBC100 unit has support for various off-the-shelf USB printers, supporting both
inkjet and laser printers. Thanks to its built-in internet protocol suite, every aspect of SCBC100 device
can be controlled remotely from anywhere around the world.
Automatic Ring and Ball Apparatus
The SCTAS-0128 Automatic Ring and Ball Apparatus is an innovative microprocessor controlled
automatic tester which is used to determine the softening point of bituminous materials using water
or glycerol as the heating fluid.
The softening point determines a disk of the sample held within a horizontal ring is forced downward
a distance of 25.4 mm under the mass of a steel ball as the sample is heated at a prescribed rate in a
water or glycerine bath.
Bitumen Oven for RTFOT
SCTAS–0140 Bitumen Oven is used for determination of the resistance to hardening of semisolid asphaltic materials/ bitumen or bituminous binders under the combined effects of heat and air with the rolling thin-film oven test (RTFOT) method. The Internal chamber of SCTAS-0140 Bitumen Oven is manufactured from
stainless steel, insulated with fiberglass or similar, the door has a symmetrically located window.
The oven has a programmable temperature controller which works in PID mode
and digital display system. A temperature sensor is used instead of the ASTM 13C thermometer. The
temperature can be read from the digital unit placed on the oven. Over temperature controlled by a
mechanic switch. Conforming to the CE Directives.
Bitumen Oven for Thin Film Oven Test
SCTAS–0145 Bitumen Oven is used for determining the loss in mass, of oil and asphaltic / bituminous
compounds when heated with the loss on heating test method or the effect of heat and air on
semisolid asphaltic / bituminous materials with the thin film oven test (TFOT) method.
The internal chamber of the SCTAS-0145 Thin Film Bitumen Oven is made of stainless steel and the
door has a panel window.
The Centrifuges are used for the determination of the bitumen percentage in bituminous mixtures.
All models comprise a removable precision-machined rotor bowl housed in a cylindrical aluminum
box. The bowl is driven by an electric motor fitted with an AC drive (inverter) with the double
function of speed control up to 3600 rpm regardless of the frequency (50 or 60 Hz) and electrical
breaking. The centrifuge can be set for the automatic speed ramp up to 3600 rpm and will stop in 10-
Cleveland Flash Tester
The SCTAS-0350 Cleveland Flash Tester is used to determine the flash and fire point of petroleum products. It consists of a brass cup mounted on an electric heater with a temperature controller and a thermometer. Conforming to the CE European Directive, the unit is supplied complete with a double line-fuse, Hot plate control apparatus and a thermometer -6 C to +400 C.
Core Drilling Machine
Machine is designed to cut cores up to 150 mm diameter from concrete, asphalt and similar hard construction materials. The machine comprises a vertical support column which carries the drill head/motor assembly. The motor assembly comprises a 6.5 Hp petrol engine. A ball screw mechanism enables close control of the drilling
pressure and rapid return when drilling is completed. A water spraying assembly is mounted on the machine. The complete assembly is supplied on a rigid wheel mounted metal base frame with leveling and
fixing facility during the operation.
Coring Bits should be ordered separately.
Core Drilling Machine
Portable SCTAS-0105 Core Drilling Machine is designed to cut cores up to 150 mm diameter from
concrete, asphalt and similar hard construction materials. The machine comprises a vertical support
column which carries the drill head/ motor assembly. The motor assembly comprises a 6.5 hp petrol engine.
A ball screw mechanism enables close control of the drilling pressure and rapid return when
drilling is completed. A water spraying assembly is mounted on the machine.
- Strength of Material
- Process Control Engineering
- Telecom Trainers
- Refregeneration Engineering
- Other Trainers
- Boilers & SteamGens
- CNC Trainers
- Electronic Trainer
- Environmental Trainers
- Fluid Mechanics
- uP Trainers
- Civil Engineering Products
- About Us
- Contact Us